Camera Company
Company
Shop By Category
T&Cs
Shop Online
  • The maker's specifications on every page
  • Free tracked USA-wide delivery over $150
  • 14-day returns

Mini Extendable Tripod | Tabletop tripod with ball head | Vlog tripod and selfie stick

Mini Extendable Tripod with 360 Ball Head and Cold Shoe

$47.99 $57.99 Save $10
  • Pocket Sized Build
  • 360 Degree Ball Head
  • Cold Shoe On The Head
  • Rubberized Handle

Price: $47.99 $57.99

  • Free tracked USA-wide delivery on orders $150+, otherwise a flat $20
  • Pay by card or PayPal, handled by the payment provider
  • 14 days to change your mind, plus your statutory rights
Product specifications
Model NameMT-16
Model NumberMT-16
Closed Length22.5 cm
Extended Length44 cm at full extension (4 levels: 27, 33, 38.5 and 44 cm)
Leg Diameter1.5 cm
Item Weight170 g
Weight Limit0.5 kg (500 g bearing weight in vertical mode)
Head TypeBall head
Mounting ScrewUniversal 1/4 inch
Compatible DevicesCamcorder, camera, cellphone, monitor, projector
Special FeatureLightweight
ColorBlack
MaterialRubber
Water ResistanceNot water resistant
Number Of Items1
Weight170 g
Shipping & returns

Tracked delivery anywhere in the USA. It is free on orders of $150 or more, and a flat $20 below that.

If it is not right for you, send it back within 14 days of delivery in resaleable condition and we refund the price you paid, including standard delivery. That is a voluntary policy we offer on top of your legal rights. You cover the cost of returning it unless the item is faulty.

If it arrives faulty, damaged or not as described, we put it right at no cost to you under the consumer protection law of your state and the Federal Trade Commission Act, return postage included.

Shipping details · Refunds and returns

Pocket Sized BuildCloses to 22.5 cm and weighs 170 g, so it rides in a jacket pocket.
360 Degree Ball HeadSwing to any angle, including upright framing for vertical video.
Cold Shoe On The HeadAdd a small microphone or LED light without a separate bracket.
Rubberized HandleSoft rubber gives a comfortable, non-slip hold when used as a grip.

A mini extendable tripod that slips in a jacket pocket and sets up your shot in seconds.

Closes to 22.5 cm, extends in 4 levels to 44 cm and weighs 170 g, with a 360 degree ball head, a cold shoe for a mic or light, and a universal 1/4 inch screw.

This mini extendable tripod closes down to 22.5 cm, extends in 4 levels to 44 cm and weighs only 170 g, which makes it easy to carry all day.

The 360 degree ball head lets you tilt and rotate to any angle, including vertical framing for phone-style video.

A cold shoe sits on the head so you can mount a small microphone or LED light while you shoot.

The universal 1/4 inch screw fits compact cameras, action cameras, camcorders and most small rigs.

Extended, it doubles as a handle grip or a short selfie stick for walk-and-talk clips.

Mini Extendable Tripod with 360 Ball Head and Cold Shoe

Small tripods usually ask you to give something up. Either they are tiny and wobbly, or they are stable and too big to carry. This one sits in the middle. Closed it measures 22.5 cm and weighs 170 g, which is light enough that you stop thinking about it, and solid enough to park a compact camera on a table and walk away from the shot.

Mini Extendable Tripod with 360 Ball Head and Cold Shoe

The head is a 360 degree ball head, so you loosen the knob, point the camera where you want it, and lock it again. That includes rolling the camera onto its side for upright video, which is how most short-form clips get shot now. There is no separate pan lock to learn, just one adjustment that handles tilt, roll and rotation together.

Mini Extendable Tripod with 360 Ball Head and Cold Shoe

On the side of the ball head sits a cold shoe. That is the small slot that takes a microphone or an LED video light. Having it built into the head means your accessory moves with the camera instead of pointing off in its own direction, and you are not stacking a separate bracket onto the rig before you can start.

Mini Extendable Tripod with 360 Ball Head and Cold Shoe

The legs and body are finished in rubber. It feels better in the hand than bare metal in cold weather, and it stops the tripod sliding around on a smooth desk or café table. Closed up, the whole thing works as a handle grip for handheld walking shots, and the center section extends in 4 levels to 44 cm when you want it as a selfie stick.

Mini Extendable Tripod with 360 Ball Head and Cold Shoe

The mount is a universal 1/4 inch screw, which is the standard thread on compact cameras, action cameras, 360 cameras and small camcorders. The stated weight limit is 0.5 kg, so it is built for light gear rather than a full-size body with a long lens. Within that limit it is a genuinely useful piece of gear to keep in a bag.

Not sure yet? That is fine.

A camera has to suit the job you bought it for, and you cannot always judge that from a photograph. If it is not right for you, send it back within 14 days of delivery in resaleable condition and we refund the price you paid, including standard delivery. That is a voluntary policy we offer on top of your legal rights.

If it turns up faulty, damaged or not as described, that is on us. The consumer protection law of your state covers you, and we pay the return postage. Read the full detail on our refunds and returns page, or ask us anything before you order.

Frequently Asked Questions

What is this product?

It is a mini extendable tripod with a 360 degree ball head and a built-in cold shoe. It closes to 22.5 cm, extends in 4 levels and weighs 170 g. You can stand it on a surface or hold it closed as a grip.

How tall does it stand?

Closed, it is 22.5 cm long. The maker shows 4 levels of extension at 27, 33, 38.5 and 44 cm. Treat it as a tabletop and handheld support rather than a standing tripod.

How much weight can it hold?

The stated weight limit is 0.5 kg, and the maker notes 500 g as the bearing weight in vertical mode. The maker points heavy cameras to a different, higher-rated model, so check your camera's weight with its lens before you buy.

What size screw does it use?

It uses a universal 1/4 inch screw, which is the standard tripod thread on most cameras and camera accessories. If your device has that threaded socket on the base, it will fit. No adapter is needed for standard gear.

Does a phone holder come with it?

No, a phone holder is not included. You would need a separate 1/4 inch phone clamp if you want to mount a phone.

Can I shoot vertical video with it?

Yes. The ball head rotates a full 360 degrees and will tip the camera onto its side for upright framing. Lock the knob once the angle looks right so it holds position.

What is the cold shoe for?

A cold shoe is a passive mounting slot for accessories. The maker names a microphone and an LED video light as the accessories it is for. It sits on the side of the ball head and is a mount only.

Is this one of the best mini tripods for vlogging?

It covers the usual vlogging needs in one small package, with a grip, a tabletop stand, a vertical-capable head and an accessory shoe. The 0.5 kg limit is the thing to check against your camera. Light compact bodies and action cameras are the sweet spot.

Can I use it as a selfie stick?

Extended, it works as a selfie stick or handle. It reaches 44 cm at full extension, so expect a modest distance rather than a wide group shot. For walk-and-talk clips that distance is usually what you want.

Will it work with an action camera?

Yes. The maker names action cameras among the devices the 1/4 inch screw is compatible with, and its photos show one mounted with a small action camera adapter. Weight is rarely an issue with cameras in that class.

Does it suit a 360 camera?

A 360 camera with a standard 1/4 inch base will thread on fine and sits well within the weight limit. Keep in mind the tripod body will appear in the lower part of a 360 capture, as any support does. Slim supports make that easier to patch out.

Can I mount a DSLR on it?

The maker lists DSLR cameras as compatible with the 1/4 inch screw, but also gives a 0.5 kg limit and tells buyers with heavy cameras to choose a higher-rated model. Weigh your body and lens together first. This is designed for compact and lightweight gear.

Is it stable enough for long exposures?

On a solid, level surface with a light camera, it will hold still for short exposures and timers. Very long exposures benefit from any extra mass and a larger footprint, so results will depend on your camera and the surface. Avoid touching the camera during the shot.

What is the body made from?

The listed material is rubber. That gives a comfortable hold in the hand and reduces slipping on smooth surfaces. Internal components are not specified by the maker.

What color is it?

Black. A plain finish keeps it unobtrusive in reflections and on a desk. The ball itself is red, as the photos show.

How much does it weigh?

170 g. That is light enough to leave in a bag permanently without noticing it. Most people carry it in a jacket pocket or a camera pouch.

Is it waterproof?

No, it is listed as not water resistant. Keep it out of rain and away from spray, and dry it off quickly if it gets damp. Salt water in particular is hard on small moving joints.

Does the ball head lock firmly?

The ball head locks with a knob you tighten by hand once the angle is set. Snug is enough, since overtightening puts strain on the mechanism. Always loosen the knob before repositioning rather than forcing the camera.

Can I use it on uneven ground?

You can, but a flat surface gives far better results with a tripod this size. On soil or gravel, press the legs down and check the camera sits level before letting go. On rock or sand, hold the grip instead.

Is this a good tabletop tripod for a camera?

It is built for exactly that job. Place it on a desk, table or counter, set the angle with the ball head, and the rubber contact points help it stay put. It is one of the easier desk tripods for streaming setups with a small camera.

Will it fit in a backpack?

Easily. At 22.5 cm closed, it slides into a side pocket, a laptop sleeve or a camera cube.

Can I attach a microphone and a light at once?

There is one cold shoe on the head, so one accessory mounts directly. To run both, you would need a dual shoe bracket that screws or clips in. Check the combined weight stays within the 0.5 kg limit.

How do I clean it?

Wipe it with a dry or lightly damp cloth and let it dry fully before folding. Brush grit off the joints rather than rinsing. Avoid solvents, which can degrade rubber over time.

Does it need any assembly?

The maker does not describe any assembly. You unfold the legs, thread your camera onto the 1/4 inch screw and set the angle.

Is it suitable for travel and hiking?

Its size and 170 g weight are the main reason to pick it for travel. It adds almost nothing to a day pack and is quick to deploy on a wall, bench or rock. Just keep it dry, since it is not water resistant.

Can I use it for product photography?

Yes, for small setups. A compact camera on a desk with the ball head angled down handles flat lays and small objects well. For overhead shots at height you would want a taller support or an arm.

How is this different from a full-size tripod?

A full-size tripod gives you eye-level height and a much higher weight rating, at the cost of bulk. This one trades height for portability and speed. Most people own both and reach for whichever fits the day.

What happens to shipping and delivery?

Orders ship by tracked delivery to US addresses only, and most arrive in 3 to 8 business days. Shipping is free on orders of $150 or more and a flat $20 under that. If anything looks delayed, contact us with your order number.

Does it make a good gift?

It is a safe gift for anyone who shoots video on a compact or action camera, since the 1/4 inch thread is near universal. It is small enough to mail easily and pairs well with a microphone or light. Mention the 0.5 kg limit if they own heavier gear.

What if it is not right for me?

Returns are accepted within 14 days of delivery if the item is in resaleable condition with its packaging, and you pay the return shipping. Get in touch with your order number and we will walk you through it. If a part arrived damaged, send a photo with your message.

How to Choose a Mini Tripod for Vlogging and Travel

6 min read Camera Company

The problem with carrying a tripod

Most people buy a tripod, use it twice, and then leave it at home. Not because it is bad, but because it is annoying. A full-size tripod is long, awkward to strap to a bag, and takes a minute to set up. By the time it is ready, the moment you wanted has usually gone.

That gap is where a mini tripod earns its place. It is not trying to replace the big one. It is trying to be the tripod that is actually with you when a shot appears. If it fits in a jacket pocket and weighs about as much as a phone, you stop making decisions about whether to bring it.

This model closes to 22.5 cm and weighs 170 g. Those two numbers explain almost everything about how it gets used. It lives in the bag, comes out in seconds, and goes back without ceremony.

What this tripod actually does

There are three jobs here, and the design is built around switching between them quickly.

The first is a tabletop stand. Open the legs, set it on a desk, table, wall or bench, and you have a stable base for a compact camera. The rubber body helps it grip smooth surfaces instead of sliding when you nudge the camera.

The second is a handle grip. Keep the legs closed and hold it like a short handle. For handheld walking shots this is better than gripping the camera directly, because your hand is further from the body and small wobbles get damped out a little. It also saves your fingers from blocking a microphone port.

The third is a selfie stick. The center section extends in 4 levels, to 27, 33, 38.5 and 44 cm, which puts a bit of distance between you and the lens. It is not a long pole, so do not expect to fit six people in a group shot.

The ball head, and why it matters

The head is a 360 degree ball head. In plain terms, the camera sits on a ball that can roll in any direction, and one knob tightens to hold it there. Loosen, point, tighten. That is the whole operation.

Compared to a pan and tilt head, which has separate controls for each axis, a ball head is faster but slightly less precise. For video and casual photography, faster usually wins. You will spend less time fiddling and more time shooting.

The important part here is vertical. Because the ball rolls freely, you can tip the camera onto its side and frame upright. That is the standard aspect for short-form video now, and plenty of cheap mini tripods cannot do it at all without an extra bracket.

A note on habit: always loosen the knob before you move the camera. Forcing a locked ball head is the single fastest way to wear out a small tripod. Hand tight is also enough when you lock it. Cranking it harder does not make it hold better, it just stresses the parts.

The cold shoe

On the side of the head sits a cold shoe. If you have not used one, it is the slot that accessories slide into, the same shape as the hot shoe on a camera. A cold shoe is a mount, nothing more.

The maker names two uses for it: a microphone for voice recording and an LED video light. A small microphone is the common choice, because built-in camera audio is often the weak point of a vlog.

Having the shoe on the head rather than the leg means your accessory follows the camera when you change angle. Tilt down for a close-up and the microphone tilts with it. That sounds minor until you have used a rig where it does not.

There is one shoe, so one accessory mounts directly. If you want a microphone and a light together, you need a small dual bracket. Just watch the total weight.

Weight limits, honestly

The stated limit is 0.5 kg. Pay attention to that number, because it is the main thing that decides whether this tripod suits you.

Half a kilo covers a lot of gear. Action cameras, 360 cameras, pocket gimbals, most compact cameras and plenty of small camcorders all sit comfortably under it. Add a light microphone and you are usually still fine.

The maker lists several compact and mirrorless bodies and DSLR cameras as compatible with the screw, and in the same breath tells buyers with a heavy camera to pick a higher-rated model. Cameras are heavier than people think once the lens is on, so weigh yours. If it is over the limit, you want a support rated for more weight.

The maker gives 500 g as the bearing weight in vertical mode. A camera rolled onto its side puts the load off to one side, which asks more of the head, so stay inside that figure.

Who this suits

If you shoot video on a compact or action camera and you travel light, this is an easy pick. It is one of the better compact travel tripods in the sense that matters most, which is that it actually gets carried.

It suits desk use too. A small camera on a table for streaming, calls or recording a how-to sits at a workable height on a stand that goes from 22.5 cm to 44 cm, and the ball head lets you angle it down at your hands or workspace.

It suits people who want to add a microphone without building a rig. The cold shoe takes care of that in one step.

It does not suit heavy cameras, and it does not suit anyone who needs eye-level height from the tripod itself. Those are different tools.

Looking after it

The care list is short. Wipe it with a dry or lightly damp cloth, and dry it fully before you fold it away. It is not water resistant, so keep it out of rain and well away from salt spray. Sand and grit are the real enemies of small joints, so brush them off rather than rinsing.

Store it folded, preferably in a pouch or a bag pocket, so the 1/4 inch thread stays clean. A thread full of lint takes longer to start than you would like when you are trying to catch a shot.

And again, loosen before you move. That one habit is kind to a ball head.

How to decide between models

If you are comparing small tripods, check four things in this order. First, the weight limit against your camera with its lens and any accessory. Second, whether the head can roll for vertical, if you shoot upright video. Third, whether there is an accessory mount, because adding one later is fiddly. Fourth, folded size, since that decides whether it travels.

Price tends to track build quality in the head more than the legs. A cheap head that creeps under load is more frustrating than slightly thin legs, because creep ruins shots while you are not looking.

The short version

This is a 170 g mini extendable tripod that closes to 22.5 cm, extends to 44 cm, carries up to 0.5 kg, and has a 360 degree ball head plus a cold shoe for a microphone or light. It mounts with a universal 1/4 inch screw, it is finished in rubber, and it is black. A phone holder is not included and it is not water resistant.

If your camera is light and you want something that is always in the bag, it does the job. If your camera is heavy, look at a larger support instead.

Browse the shop

Not sure if it fits your camera?

Check your camera's weight and look for the 1/4 inch thread on its base, then message us if you want a second opinion.

Ask us a question

Page summary

This is a mini extendable tripod for compact cameras, action cameras, camcorders and small rigs. It closes to 22.5 cm, extends in 4 levels to 44 cm, weighs 170 g and has a stated leg diameter of 1.5 cm. The head is a 360 degree ball head that supports vertical shooting, and it carries a cold shoe for mounting a small microphone or LED light. The mount is a universal 1/4 inch screw and the stated weight limit is 0.5 kg, with 500 g given as the bearing weight in vertical mode. Body material is listed as rubber and the color is black. It is not water resistant. A phone holder is not included. Brand, country of origin and overall packed dimensions are not specified by the maker.